Hydraulic spindles and cylinders
A hydraulic spindle replaces the mechanical spindle on your puller cross-arm. That turns an ordinary puller into a hydraulic one. Check the spindle number on the cross-arm first, then you know which size fits. The spindles run from 12 to 20 tonnes of pulling force. There are short and long versions, with a thread or a G 3/4" connection. Hollow ram cylinders run off a separate pump and hose. See hydraulic pullers for the complete build of cross-arm, spindle and pressure piece.
KUKKO K-8-HP-623 Hydraulic spindle with hand lever operation in case, up to 6 t pulling force (thread size)
KUKKO K-8-HP-633 Hydraulic spindle with hand lever operation in case, up to 12 t pulling force (thread size)
KUKKO K-8-HP-637 Hydraulic spindle with hand lever operation in case, up to 15 t pulling force (thread size)
KUKKO Y-19-17 Pressure piece set for shaft bores Ø 33 - 81 mm
KUKKO Y-20-17 Pressure piece set for shaft bores Ø 55 - 88 mm
KUKKO Y-60-100-17 Pressure piece set for shaft bores Ø 64 - 70 mm
KUKKO YM-235 700 bar pressure gauge
KUKKO 8-HP-621 Hydraulic spindle with hand lever operation, up to 20 t pulling force
KUKKO K-8-HP-621 Hydraulic spindle with hand lever operation in case, up to 4 t pulling force (thread size)
KUKKO K-8-HP-800 Hydraulic spindle with hand lever operation in case, up to 20 t pulling force (thread size)
KUKKO 8-HP-637 Hydraulic spindle with hand lever operation, up to 20 t pulling force
KUKKO Y-AP-373 Bolt, Glue clamps set MB
KUKKO YRH-302 Hollow piston cylinder with max. 30 t pulling force, 63 mm stroke, external thread pressure cylinder 4 1/2"-12 UN
KUKKO YSM-200 Impact cylinder with max. 20 t pulling force, 11 mm stroke
KUKKO YDM-20E Pressure pieces for hollow piston cylinders
KUKKO K-8-HP-626 Hydraulic spindle with hand lever operation in case, up to 12 t pulling force (thread size)
KUKKO YF-200 2 m hose
KUKKO YHP-326 Hand pump with hose, pressure gauge, metal case
KUKKO YHP-420 Hand pump
KUKKO YHP-424 Hand pump with pressure gauge
KUKKO Y-18-17 Pressure piece set for shaft bores Ø 20 - 62 mm
KUKKO 8-HP-800 Hydraulic spindle with hand lever operation, up to 20 t pulling force
KUKKO YRH-202 Hollow piston cylinder with max. 20 t pulling force, 50 mm stroke, external thread pressure cylinder 3 7/8"-12 UN
KUKKO YRE-050 Hydraulic pressure cylinder with collar thread 1 1/2"-16UN, max. 5 t pulling force
KUKKO YRE-101 Hydraulic pressure cylinder with collar thread 2.1/4"-14 UNS, max. 10 t pulling force
Which hydraulic spindle or cylinder fits your puller?
Which size spindle do you need?
A hydraulic spindle replaces the mechanical spindle on your puller cross-arm. Look up the spindle number on the cross-arm first. That number decides the size and the connection. If the spindle does not fit, you will not get it mounted. The range runs from 12 to 20 tonnes of pulling force. Use short spindles where there is little room, long ones where you have to reach further.
Grease-hydraulic or hollow ram cylinder?
Grease-hydraulic spindles have a built-in pump and run on grease. You do not need a separate hose. Hollow ram cylinders go on an external pump with a hose. That combination gives more force for heavy work. Look at the space around the cross-arm and at the force you need. For the loose spindles in this category, such as the 12-tonne spindle with G 3/4" connection, the rule is: measure the thread if the number is not readable.
What to check when you order?
Check the bore of the pressure piece. It has to fit the shaft you want to pull. Pressure piece sets come for different shaft bores, from 20 to 68 millimetres. Measure the shaft accurately. If you order a long version, check whether the stroke suits the space you have. If you are unsure between two sizes, take the spindle you can find on the cross-arm.